1sd418f2 igbt-driver.com page 1 data sheet 1SD418F2-FX800R33KF2 single-channel scale plug-and-play igbt driver ultra-compact, high-performance driver for 2-level, 3-level and multilevel converters abstract the scale plug-and-play driver 1sd418f 2-fx800r33kf2 is an ultra-compact single-channel intelligent gate driver de signed for infineon?s high-voltage igbts of type fd800r33kf2 and fz800r 33kf2. the driver features a fiber- optic interface, a built-in dc/dc power supply and a selectable operating mode via a jumper. for drivers adapted to other types of high-p ower and high-voltage igbt modules, refer to www.igbt-driver.com/go/plug-and-play product highlights applications [ plug-and-play solution [ three/multi-level converters [ protects the igbt from short-circuit failure [ two-level converters [ active clamping of v ce at turn-off [ medium-voltage converters [ extremely reliable; long service life [ industrial drives [ no electrolytic capacitors [ traction [ gate current up to 18a [ railroad power supplies [ electrical insulation 6000 v ac [ wind-power converters [ fiber-optic links [ radiology and laser technology [ monitoring of supply voltage and fiber optics [ research [ switching frequency dc to max. 6khz [ almost all other conceivable [ duty cycle 0... 100% applications [ built-in dc/dc power supply [ shortens application development time
1sd418f2 data sheet 1SD418F2-FX800R33KF2 page 2 ct-concept.com important notes this data sheet contains only product-specific data. for a detailed description, must- read application notes and comm on data that apply to the whole series, please refer to the ?description & applicatio n manual for 1sd418f2 scale high-voltage igbt drivers?. when applying scale plug-and-play driver s, please note that these drivers are specifically adapted to a particular type of igbt module. therefore, the type designation of scale plug-and-play drivers al so includes the type designation of the corresponding igbt module. these drivers are not valid for igbt modules other than those specified. incorrect use may result in failure. mechanical and electrical interfaces dimensions: 183 x 38 (47) mm . mounting principle: dir ect screw mount on igbt. interface remarks part type # drive signal input fiber-optic receiver (notes 16,18) hfbr-2522 status output fiber-optic transmitter (notes 16,19) hfbr-1522 power supply connector on-board connector (note 17) 77315-101-05 power supply connector designator pin numbers ground gnd 1, 2, 4, 5 supply voltage v dc 3 absolute maximum ratings parameter remarks min max units supply voltage v dc vdc to gnd (note 1) 0 16 v gate peak current i out note 8 -18 +18 a average supply current i dc note 3 400 ma output power dc/dc converter notes 3,12 4 w switching frequency note 12 6 khz test voltage (50hz/1min) primary to output (note 15) 6000 v ac(eff) dc-link voltage note 5 2200 v operating temperature note 12 -40 +85 c storage temperature -40 +90 c
1sd418f2 data sheet 1SD418F2-FX800R33KF2 igbt-driver.com page 3 electrical characteristics all data refer to +25c and v dc = 15v unless otherwise specified power supply remarks min typ. max units nominal supply voltage v dc vdc to gnd (note 1) 14.5 15 15.5 v supply current i dc without load (note 2) 120 ma efficiency i nternal dc/dc converter 85 % turn-on threshold v th note 4 13 v hysteresis on/off note 4 0.7 v coupling capacitance c io primary to output 15 pf short-circuit protection remarks min typ. max units v ce monitoring threshold betw een aux. terminals 50 60 v response time 3-level mode (note 11) 8.2 8.8 s response time 2-level mode (note 6) 9.3 10 s blocking time 2-level mode (note 7) 1 s timing characteristics remarks min typ. max units turn-on delay t pd(on) note 13 400 ns turn-off delay t pd(off) note 13 550 ns output rise time t r(out) note 9 100 ns output fall time t f(out) note 9 100 ns acknowledge delay time at status output (note 14) 450 ns acknowledge pulse width at status output 0.7 1.8 s gate output remarks min typ. max units turn-on gate resistor r g(on) note 8 2.1 ? turn-off gate resistor r g(off) note 8 3.4 ? aux. gate capacitor c ge 220 nf electrical insulation remarks min typ. max units operating voltage (note 10) continuous or repeated 3300 v test voltage (50hz/1min) primary to output (note 15) 6000 v ac(eff) partial discharge extinction volt. iec1287 / <10pc 2600 v ac(eff) creepage distance primary to output 20 mm
1sd418f2 data sheet 1SD418F2-FX800R33KF2 page 4 ct-concept.com footnotes to the key data 1) supply voltages higher than those specified can le ad to the destruction of the driver and protection circuits on the output side. the gate-emitter vo ltage tracks the primary supply voltage. (not regulated by the supply circuitry or the gate drive unit.) 2) static power consumption of the gate driver. 3) if the specified power consumption is exceeded on average, this indicates an overload of the dc/dc converter. the dc/dc converter is not protected against overload. 4) under-voltage monitoring of power supply. for a voltage lower than this limit, the power modules are switched off. the voltage refers to the seco ndary supply voltage of the gate driver, which is approximately the same as the voltage between vdc and gnd. 5) this limit is due to active clamping. refer to the ?description and application manual for 1sd418f2 scale high-voltage igbt drivers?. 6) pulse width of the direct output of the gate drive unit. (excluding the delay of the gate resistors.) 7) duration of blocking the command input (keeping the gate driver and the igbt in the off-state) after fault detection, i.e. power supply under-volt age lock out, or ? only in 2-level mode ? short- circuit detection. (for three/multilevel mode, turn -off under the short-circuit condition is managed by the host controller.) 8) the gate current is limited by on-board gate resistors. 9) refers to the direct output of the gate drive unit. (excluding the delay of the gate resistors.) 10) maximum continuous or repeatedly applied dc vo ltage or peak value of the repeatedly applied ac voltage between the power supply in puts and all other terminals. 11) including the delay of external fiber optic links. measured from turn-on transition at direct output of the gate drive unit (not covering the delay of the gate resistors) to the transition of status signal at the host controller side optical receiver. 12) application-specific self-heating of gate drivers and igbt modules, especially at high switching frequency, must be taken into account. the switching frequency is commonly limited due to switching losses of the igbt mo dules. because concept cannot predict how the drivers will be incorporated in the user?s application, no bindin g recommended value for self-heating and thus for the maximum useable output power can be made. it is therefore recommended to check the gate driver?s ambient temperature within the system. 13) including the delay of external fiber-optic links. me asured from the transition of turn-on or turn-off command at the optical transmitter on the host cont roller side to direct output of the gate drive unit. (excluding the delay of the gate resistors.) 14) including the delay of external fiber-optic links. me asured from the transition of turn-on or turn-off command at the optical transmitter on the host cont roller side to the transition of the acknowledge signal at the optical receiver on the host controller side. 15) the test voltage may be applied only once during one minute. it should be noted that with this (strictly speaking obsolete) test method, some (min or) damage occurs to the insulation layers due to the partial discharge. consequently, this test is not performed at concept as a series test. in the case of repeated insulation tests (e.g. module test, equipment test, system test) the subsequent tests should be performed with a lower test voltage: the test voltage is reduced by 10% for each additional test. the more modern if more elaborate partial-discharge measurement is better suited than such test methods as it is almost entirely non-destructive. 16) the transceivers required at the host controller side are not delivered with the gate driver. it is recommended to use the same types as used in th e gate driver. for product information refer to www.igbt-driver.com/go/fiberoptics 17) the customer-side connector is not supplied with the gate driver, but via fci inc. recommended crimp contact housing: order code 65039-032; recommended crimp contacts: 5 pcs , order code 48236-002. refer to www.igbt-driver.com/go/fci 18) the recommended transmitter current at the host controller is 30-35ma, suitable for plastic optic fibers with a length of less than 2.5 meters. higher current may increase jitter or delay at turn-off. 19) the transmitter current at the gate driver is 30-35ma.
1sd418f2 data sheet 1SD418F2-FX800R33KF2 igbt-driver.com page 5 important notice the data contained in this product data sh eet is intended exclusively for technically trained staff. handling all high-voltage equi pment involves risk to life. strict compliance with the respective safety regulations is mandatory! any handling of electronic devi ces is subject to the genera l specifications for protecting electrostatic-sensitive devices according to international st andard iec 747-1, chapter ix or european standard en 100015 (i.e. the wo rkplace, tools, etc. must comply with these standards). otherwise, this product may be damaged. disclaimer this data sheet specifies devices but cannot promise to deliver any specific characteristics. no warranty or guarantee is given ? either expre ssly or implicitly ? regarding delivery, perf ormance or suitability. ct-concept technology ag reserves the righ t to make modifications to its technical data and product specifications at any time without prior notice. the general terms and conditions of delivery of ct-c oncept technology ag apply.
1sd418f2 data sheet 1SD418F2-FX800R33KF2 page 6 ct-concept.com ordering information the general terms and conditions of deliver y of ct-concept technologie ag apply. related igbt concept driver type # infineon (eupec) fd800r 33kf2 1SD418F2-FX800R33KF2 infineon (eupec) fz800r 33kf2 1SD418F2-FX800R33KF2 information about other products for drivers adapted to other high-vol tage or high-power igbt modules direct link: www.igbt-driver.com/go/plug-and-play for other drivers and evaluation systems please click: www.igbt-driver.com manufacturer ct-concept technologie ag intelligent power electronics renferstrasse 15 ch-2504 biel-bienne switzerland tel. +41 - 32 - 344 47 47 fax +41 - 32 - 344 47 40 e-mail info@igbt-driver.com internet www.igbt-driver.com ? copyright 1999...2007 by ct-concept technologi e ag - switzerland. all rights reserved. we reserve the right to make any technical modifi cations without prior notice. version from 2007-06-06
|
